whefreak.blogg.se

Evolution 200 insinkerator manual
Evolution 200 insinkerator manual







evolution 200 insinkerator manual

Instead, turn the water and disposer on first and then feed the peels in gradually. Don’t fill disposer with a lot of vegetable peels all at once.It is OK to drain hot water into the disposer between grinding periods. Don’t use hot water when grinding food waste.PUT GREASE IN A JAR OR CAN AND DISPOSE IN THE TRASH. IT CAN BUILD UP IN PIPES AND CAUSE DRAIN BLOCKAGES. DON’T POUR GREASE OR FAT DOWN YOUR DISPOSER OR ANY DRAIN.After grinding is complete, turn disposer off and run water for a few seconds to flush drain line.WARNING! Position stopper to minimize possible ejection of material while grinding. Slowly insert food waste into disposer.Remove stopper from sink opening and run cold water.Fill sink with water, then test for leaks. Insert Quiet Collar® Sink Baffle into sink opening. Make sureĪnti-Vibration Tailpipe Mount™ is straight. Reconnect plumbing (and dishwasher connection if used). You may need to trim tube for proper fit. Turn mounting ring until all 3 mounting tabs lock over the ridges on the slide-up ramps. Hang disposer by aligning 3 mounting tabs with slide-up ramps on mounting ring. ĬAUTION: Do not position your head or body under disposer unit could fall during removal or installation.ĭetach removable portion of spec label and place on a visible location after installation.Important: Failure to use the spring type hose clamp provided voids warranty. Place tube (M or N) into Anti-Vibration Tailpipe Mount™. Push wires into disposer (do not displace cardboard shield) and replace electrical cover plate. Unit must be grounded for safe and proper installation Connect white wire from disposer to neutral (white) wire from power source and black wire from disposer to hot (black, red) wire from power source with wire nuts (not included) ground wire to green grounding screw. WARNING! Improper grounding can result in electric shock hazard.

evolution 200 insinkerator manual

This disposer requires a switch (15 amp minimum rating) with a marked “Off” position (wired to disconnect all ungrounded supply conductors) installed within sight of the disposer sink opening, except if using an air switch or batch feed accessory, or batch feed disposer. Insert cable connector (not included) and run electrical cable through access hole on bottom of disposer. Turn disposer over and remove electrical cover plate. Knock out drain plug and remove plug from inside of disposer. Turn disposer (J) onto side and insert screwdriver into dishwasher inlet. If you do not need to attach the dishwasher, go to Step 16. Use shorter 1-1/8” screws (H) if sink is more than 3/8” thick. Tighten 1-1/2” screws (G) evenly and firmly against backup flange. Pull snap ring (I) open and press firmly until it snaps into place. Place a weight such as the disposer on the sink flange to hold it in place. Hold flange (C) in place while inserting snap ring (I). Insert fiber gasket (D), backup flange (E) and mounting ring (F).

  • Įvenly apply 1/2” thick rope of plumber’s putty around flange (C).
  • Remove old plumber’s putty from sink with putty knife.

    evolution 200 insinkerator manual

    Using a screwdriver, remove the snap ring. Loosen the 3 screws on the mounting assembly. ĭisconnect the disposer wires from the electrical supply.įlip disposer over and remove electrical cover plate.Support disposer, insert end of Jam-Buster™ Wrench (K) into right side of mounting lug, and turn. ĭisconnect drain trap from waste discharge tube.If there is no existing disposer, disconnect sink drain and skip to Step 9. If you are replacing an existing disposer, continue to Step 2.NOTICE: Failure to use the spring type hose clamp provided voids warranty.









    Evolution 200 insinkerator manual